资源类型

期刊论文 541

会议视频 5

年份

2024 1

2023 42

2022 65

2021 51

2020 34

2019 49

2018 20

2017 19

2016 25

2015 8

2014 17

2013 26

2012 9

2011 23

2010 17

2009 30

2008 28

2007 24

2006 6

2005 10

展开 ︾

关键词

混凝土 16

三峡工程 9

三峡升船机 4

混凝土面板堆石坝 3

三点弯曲梁 2

仿真优化 2

升船机 2

混凝土坝 2

混凝土浇筑 2

碾压混凝土坝 2

组合梁 2

耐久性 2

自主开发 2

&ldquo 1

12相整流 1

3D打印 1

700 m跨径级别 1

ANFIS 1

ANSYS 1

展开 ︾

检索范围：

排序： 展示方式：

Compressive strength and stability of sustainable self-consolidating concrete containing fly ash, silica

Osama Ahmed MOHAMED, Omar Fawwaz NAJM

《结构与土木工程前沿（英文）》 2017年 第11卷 第4期   页码 406-411 doi: 10.1007/s11709-016-0350-1

摘要： This paper presents the findings of an experimental program seeking to understand the effect of mineral admixtures on fresh and hardened properties of sustainable self-consolidating concrete (SCC) mixes where up to 80% of Portland cement was replaced with fly ash, silica fume, or ground granulated blast furnace slag. Compressive strength of SCC mixes was measured after 3, 7, and 28 days of moist curing. It was concluded in this study that increasing the dosage of fly ash increases concrete flow but also decreases segregation resistance. In addition, for the water-to-cement ratio of 0.36 used in this study, it was observed that the compressive strength decreases compared to control mix after 28 days of curing when cement was partially replaced by 10%, 30%, and 40% of fly ash. However, a fly ash replacement ratio of 20% increased the compressive strength by a small margin compared to the control mix. Replacing cement with silica fume at 5%, 10%, 15%, and 20% was found to increase compressive strength of SCC mixes compared to the control mix. However, the highest 28 day compressive strength of 95.3 MPa occurred with SCC mixes in which 15% of the cement was replaced with silica fume.

关键词： fly ash     silica fume     ground granulated blast-furnace slag     self-consolidating concrete     and sustainable concrete    

HTML PDF 收藏

comparative study of the mechanical properties, fracture behavior, creep, and shrinkage of chemically based self-consolidatingconcrete

Mahdi AREZOUMANDI, Mark EZZELL, Jeffery S VOLZ

《结构与土木工程前沿（英文）》 2014年 第8卷 第1期   页码 36-45 doi: 10.1007/s11709-014-0243-0

摘要： This study presents the results of an experimental investigation that compares the mechanical properties, fracture behavior, creep, and shrinkage of a chemically-based self-consolidating concrete (SCC) mix with that of a corresponding conventional concrete (CC) mix. The CC and SCC mix designs followed conventional proportioning in terms of aggregate type and content, cement content, air content, water-cementitiuos materials ( / ) ratio, and workability. Then, using only chemical admixtures, the authors converted the CC mix to an SCC mix with all of the necessary passing, filling, flowability, and stability requirements typically found in SCC. The high fluidity was achieved with a polycarboxylate-based high-range water-reducing admixture, while the enhanced stability was accomplished with an organic, polymer-based viscosity-modifying admixture. The comparison indicated that the SCC and CC mixes had virtually identical tensile splitting strengths, flexural strengths, creep, and shrinkage. However, the SCC mix showed higher compressive strengths and fracture energies than the corresponding CC mix.

关键词： admixture     conventional concrete (CC)     creep     fracture mechanic     mechanical Properties     self-consolidating concrete (SCC)     shrinkage    

HTML PDF 收藏

Effect of microlimestone on properties of self-consolidating concrete with manufactured sand and mineral

Fulin Qu, Wengui Li, Xiaohui Zeng, Zhiyu Luo, Kejin Wang, Daichao Sheng

《结构与土木工程前沿（英文）》 2020年 第14卷 第6期   页码 1545-1560 doi: 10.1007/s11709-020-0678-4

摘要： Self-consolidating concrete (SCC) with manufactured sand (MSCC) is crucial to guarantee the quality of concrete construction technology and the associated property. The properties of MSCC with different microlimestone powder (MLS) replacements of retreated manufactured sand (TMsand) are investigated in this study. The result indicates that high-performance SCC, made using TMsand (TMSCC), achieved high workability, good mechanical properties, and durability by optimizing MLS content and adding fly ash and silica fume. In particular, the TMSCC with 12% MLS content exhibits the best workability, and the TMSCC with 4% MLS content has the highest strength in the late age, which is even better than that of SCC made with the river sand (Rsand). Though MLS content slightly affects the hydration reaction of cement and mainly plays a role in the nucleation process in concrete structures compared to silica fume and fly ash, increasing MLS content can evidently have a significant impact on the early age hydration progress. TMsand with MLS content ranging from 8% to 12% may be a suitable alternative for the Rsand used in the SCC as fine aggregate. The obtained results can be used to promote the application of SCC made with manufactured sand and mineral admixtures for concrete-based infrastructure.

关键词： microlimestone powder     manufactured sand     retreated manufactured sand     self-consolidating concrete     mineral admixture    

HTML PDF 收藏

Computational modeling of fracture in capsule-based self-healing concrete: A 3D study

《结构与土木工程前沿（英文）》 2021年 第15卷 第6期   页码 1337-1346 doi: 10.1007/s11709-021-0781-1

摘要： We present a three-dimensional (3D) numerical model to investigate complex fracture behavior using cohesive elements. An efficient packing algorithm is employed to create the mesoscale model of heterogeneous capsule-based self-healing concrete. Spherical aggregates are used and directly generated from specified size distributions with different volume fractions. Spherical capsules are also used and created based on a particular diameter, and wall thickness. Bilinear traction-separation laws of cohesive elements along the boundaries of the mortar matrix, aggregates, capsules, and their interfaces are pre-inserted to simulate crack initiation and propagation. These pre-inserted cohesive elements are also applied into the initial meshes of solid elements to account for fracture in the mortar matrix. Different realizations are carried out and statistically analyzed. The proposed model provides an effective tool for predicting the complex fracture response of capsule-based self-healing concrete at the meso-scale.

关键词： 3D fracture     self-healing concrete     spherical     cohesive elements     heterogeneous    

HTML PDF 收藏

Parametric study on seismic performance of self-centering reinforced concrete column with bottom-placed

《结构与土木工程前沿（英文）》   页码 1145-1162 doi: 10.1007/s11709-023-0945-2

摘要： To realize seismic-resilient reinforced concrete (RC) moment-resisting frame structures, a novel self-centering RC column with a rubber layer placed at the bottom (SRRC column) is proposed herein. For the column, the longitudinal reinforcement dissipates seismic energy, the rubber layer allows the rocking of the column, and the unbonded prestressed tendon enables self-centering capacity. A refined finite element model of the SRRC column is developed, the effectiveness of which is validated based on experimental results. Results show that the SRRC column exhibits stable energy dissipation capacity and no strength degradation; additionally, it can significantly reduce permanent residual deformation and mitigate damage to concrete. Extensive parametric studies pertaining to SRRC columns have been conducted to investigate the critical factors affecting their seismic performance.

关键词： seismic resilience     self-centering     rubber layer     flag-shaped hysteresis loop     parametric study    

HTML PDF 收藏

The effects of mismatch fracture properties in encapsulation-based self-healing concrete using cohesive-zone

Luthfi Muhammad MAULUDIN, Chahmi OUCIF, Timon RABCZUK

《结构与土木工程前沿（英文）》 2020年 第14卷 第3期   页码 792-801 doi: 10.1007/s11709-020-0629-0

摘要： Finite element analysis is developed to simulate the breakage of capsule in capsule-based self-healing concrete. A 2D circular capsule with different core-shell thickness ratios embedded in the mortar matrix is analyzed numerically along with their interfacial transition zone. Zero-thickness cohesive elements are pre-inserted into solid elements to represent potential cracks. This study focuses on the effects of mismatch fracture properties, namely fracture strength and energy, between capsule and mortar matrix into the breakage likelihood of the capsule. The extensive simulations of 2D specimens under uniaxial tension were carried out to investigate the key features on the fracture patterns of the capsule and produce the fracture maps as the results. The developed fracture maps of capsules present a simple but valuable tool to assist the experimentalists in designing appropriate capsule materials for self-healing concrete.

关键词： self-healing concrete     interfacial zone     capsule materials     cohesive elements     fracture maps    

HTML PDF 收藏

Stress-strain relationship of recycled self-compacting concrete filled steel tubular column subjected

Feng YU, Cheng QIN, Shilong WANG, Junjie JIANG, Yuan FANG

《结构与土木工程前沿（英文）》 2020年 第14卷 第3期   页码 760-772 doi: 10.1007/s11709-020-0618-3

摘要： As a typical compression member, the concrete-filled steel tube has been widely used in civil engineering structures. However, little research on recycled self-compacting concrete filled circular steel tubular (RSCCFCST) columns subjected to eccentric load was reported. In this study, 21 specimens were designed and experimental studies on the stress-strain relationship of were carried out to study the mechanical behaviors. Recycled coarse aggregate replacement ratio, concrete strength grade, length to diameter ratio and eccentric distance of specimens were considered as the main experimental parameters to carry out eccentric compression tests. The corresponding stress-strain relationship curves were used to analyze the influence of concerned parameters on eccentric load-bearing capacity of RSCCFCST columns. The experimental results show that the strain of the eccentric compression stress-strain curves increase with the increase of recycled coarse aggregate replacement ratio and concrete strength grade. With increase of eccentric distance, the ductility of specimens increases while the bearing capacity decreases. Moreover, a phenomenological model of RSCCFCST columns is proposed, which exhibits versatile ability to capture the process during loading. The present study is expected to further understanding the behaviors and to provide guidance of RSCCFCST columns in design and engineering applications.

关键词： concrete filled circular steel tubular columns     recycled self-compacting concrete     eccentric compression     recycled coarse aggregate replacement ratio     stress-strain relationship    

HTML PDF 收藏

Enhancing compressive strength and durability of self-compacting concrete modified with controlled-burnt

《结构与土木工程前沿（英文）》 2022年 第16卷 第2期   页码 161-174 doi: 10.1007/s11709-021-0796-7

摘要： In sugar industries, the growing amount of sugarcane bagasse ash (SBA), a byproduct released after burning bagasse for producing electricity, is currently causing environmental pollution. The residual ash displays a pozzolanic potential; and hence, it has potential as a cement addictive. This study focuses on enhancing suitability of SBA through incorporating ground blast furnace slag (BFS) in manufacturing self-compacting concretes (SCCs). For this purpose, SBA was processed by burning at 700 °C for 1 h, before being ground to the cement fineness of 4010 cm2/g. SCC mixtures were prepared by changing the proportions of SBA and BFS (i.e., 10%, 20%, and 30%) in blended systems; and their performance was investigated. Test results showed that the presence of amorphous silica was detected for the processed SBA, revealing that the strength activity index was above 80%. The compressive strength of SCC containing SBA (without BFS) could reach 98%−127% of that of the control; combination of SBA and 30% BFS gets a similar strength to the control after 28 d. Regarding durability, the 10%SBA + 30%BFS mix exhibited the lowest risk of corrosion. Moreover, the joint use of SBA and BFS enhanced significantly the SCC’s sulfate resistance. Finally, a hyperbolic formula for interpolating the compressive strength of the SBA-based SCC was proposed and validated with error range estimated within ±10%.

关键词： sugarcane bagasse ash     self-compacting concrete     compressive strength     sulfate resistance     water absorption     strength formula    

HTML PDF 收藏

Optimization of machine learning models for predicting the compressive strength of fiber-reinforced self-compactingconcrete

《结构与土木工程前沿（英文）》 2023年 第17卷 第2期   页码 284-305 doi: 10.1007/s11709-022-0901-6

摘要： Fiber-reinforced self-compacting concrete (FRSCC) is a typical construction material, and its compressive strength (CS) is a critical mechanical property that must be adequately determined. In the machine learning (ML) approach to estimating the CS of FRSCC, the current research gaps include the limitations of samples in databases, the applicability constraints of models owing to limited mixture components, and the possibility of applying recently proposed models. This study developed different ML models for predicting the CS of FRSCC to address these limitations. Artificial neural network, random forest, and categorical gradient boosting (CatBoost) models were optimized to derive the best predictive model with the aid of a 10-fold cross-validation technique. A database of 381 samples was created, representing the most significant FRSCC dataset compared with previous studies, and it was used for model development. The findings indicated that CatBoost outperformed the other two models with excellent predictive abilities (root mean square error of 2.639 MPa, mean absolute error of 1.669 MPa, and coefficient of determination of 0.986 for the test dataset). Finally, a sensitivity analysis using a partial dependence plot was conducted to obtain a thorough understanding of the effect of each input variable on the predicted CS of FRSCC. The results showed that the cement content, testing age, and superplasticizer content are the most critical factors affecting the CS.

关键词： compressive strength     self-compacting concrete     artificial neural network     decision tree     CatBoost    

HTML PDF 收藏

Experimental research on self-stressing and self-compacting concrete filled steel tube columns subjected

Chengkui HUANG, Zuoqing SHANG, Peng ZHANG,

《结构与土木工程前沿（英文）》 2009年 第3卷 第4期   页码 455-461 doi: 10.1007/s11709-009-0058-6

摘要： A total of fifteen self-stressing and self-compacting concrete (SSC) filled steel tube columns and three common self-compacting concrete filled steel tube (CFST) columns are tested under eccentric compression load to analyze the effect of initial self-stress on the compression behavior of CFSTs. The results show that the elastic working range of the columns is lengthened because of initial self-stress and it slightly decreases with the increase of load eccentricity ratio and slenderness ratio. Because of the initial self-stress, the concrete core is always under compression in three directions, so the compactness is enhanced and the ultimate bearing capacity obviously increases; but the initial self-stress hardly affects the failure mode of the columns.

关键词： increase     capacity     failure     CFSTs     CFST    

HTML PDF 收藏

A hybrid machine learning model to estimate self-compacting concrete compressive strength

Hai-Bang LY; Thuy-Anh NGUYEN; Binh Thai PHAM; May Huu NGUYEN

《结构与土木工程前沿（英文）》 2022年 第16卷 第8期   页码 990-1002 doi: 10.1007/s11709-022-0864-7

摘要： This study examined the feasibility of using the grey wolf optimizer (GWO) and artificial neural network (ANN) to predict the compressive strength (CS) of self-compacting concrete (SCC). The ANN-GWO model was created using 115 samples from different sources, taking into account nine key SCC factors. The validation of the proposed model was evaluated via six indices, including correlation coefficient (R), mean squared error, mean absolute error (MAE), IA, Slope, and mean absolute percentage error. In addition, the importance of the parameters affecting the CS of SCC was investigated utilizing partial dependence plots. The results proved that the proposed ANN-GWO algorithm is a reliable predictor for SCC’s CS. Following that, an examination of the parameters impacting the CS of SCC was provided.

关键词： artificial neural network     grey wolf optimize algorithm     compressive strength     self-compacting concrete    

HTML PDF 收藏

Recycled glass replacement as fine aggregate in self-compacting concrete

Yasser SHARIFI, Mahmoud HOUSHIAR, Behnam AGHEBATI

《结构与土木工程前沿（英文）》 2013年 第7卷 第4期   页码 419-428 doi: 10.1007/s11709-013-0224-8

摘要： With increasing environmental pressure to reduce solid waste and to recycle as much as possible, the concrete industry has adopted a number of methods to achieve this goal by replacement of waste glass with concrete composition materials. Due to differences in mixture design, placement and consolidation techniques, the strength and durability of Self Compacting Concrete (SCC) may be different than those of conventional concrete. Therefore, replacement of waste glass with fine aggregate in SCC should deeply be investigated compared to conventional concretes. The aim of the present study is to investigate the effect of glass replacement with fine aggregate on the SCC properties. In present study, fine aggregate has been replaced with waste glass in six different weight ratios ranging from 0% to 50%. Fresh results indicate that the flow-ability characteristics have been increased as the waste glass incorporated to paste volume. Nevertheless, compressive, flexural and splitting strengths of concrete containing waste glass have been shown to decrease when the content of waste glass is increased. The strength reduction of concrete in different glass replacement ratios is not remarkable, thus it can be produced SCC with waste glass as fine aggregate in a standard manner.

关键词： Self Compacting Concrete (SCC)     recycle glass     fine aggregate     fresh and hardened properties    

HTML PDF 收藏

Computational model generation and RVE design of self-healing concrete

Md. Shahriar QUAYUM,Xiaoying ZHUANG,Timon RABCZUK

《结构与土木工程前沿（英文）》 2015年 第9卷 第4期   页码 383-396 doi: 10.1007/s11709-015-0320-z

摘要： Computational homogenization is a versatile tool that can extract effective properties of heterogeneous or composite material through averaging technique. Self-healing concrete (SHC) is a heterogeneous material which has different constituents as cement matrix, sand and healing agent carrying capsules. Computational homogenization tool is applied in this paper to evaluate the effective properties of self-healing concrete. With this technique, macro and micro scales are bridged together which forms the basis for multi-scale modeling. Representative volume element (RVE) is a small (microscopic) cell which contains all the microphases of the microstructure. This paper presents a technique for RVE design of SHC and shows the influence of volume fractions of different constituents, RVE size and mesh uniformity on the homogenization results.

关键词： homogenization     self-healing concrete (SHC)     representative volume element     multiscale modelling    

HTML PDF 收藏

An experimental study for optimization of high range water reducing superplasticizer in self compactingconcrete

Rahul DUBEY, Pardeep KUMAR

《结构与土木工程前沿（英文）》 2013年 第7卷 第1期   页码 62-71 doi: 10.1007/s11709-013-0192-z

摘要： Concrete is extensively used construction material in the infrastructure development industry. With increase in technical knowhow, the need of research for high performance concretes such as self-compacting concrete (SCC) has increased in the last decade. The adaptability of SCC is due to its fluidic behavior in fresh state. However, to develop SCC using indigenous materials, the lack of standardized mix design procedures is the biggest impediment. Although with the advent of chemical admixtures, it is possible to achieve concrete with high fluidity, but at the same time durability issues require more attention. To have these fresh state properties SCC mixes are typically designed with high powder contents, and chemical admixtures. Proportioning and optimization of these materials is a key issue in the mix design of SCC. This paper focuses mainly on experimental study to optimize dosages of superplasticizer for mortar of SCC and then in concrete mixture itself.

关键词： self-compacting concrete (SCC)     fresh properties     superplasticizer     optimization     compressive strength    

HTML PDF 收藏

三峡升船机液压自升式模板施工技术

戴志清

《中国工程科学》 2013年 第15卷 第9期   页码 22-26

摘要：

三峡升船机塔柱混凝土施工工期紧，精度要求高，为保证施工进度和质量，采用了液压自升式模板。本文重点介绍了三峡升船机塔柱混凝土液压自升式模板施工技术、自升式模板改进措施以及为满足自升式模板上升而在塔柱板梁、牛腿处进行的结构处理措施。实践证明，液压自升式模板施工技术的应用与改进满足了三峡升船机塔柱筒体混凝土的设计要求，有效地提高施工效率、节约了成本，保证了工程质量并提高施工的安全性，可为其他水电工程施工提供借鉴。

关键词： 塔柱混凝土     液压自升式模板     混凝土浇筑     三峡升船机    

HTML PDF 收藏

标题 作者 时间 类型 操作

Compressive strength and stability of sustainable self-consolidating concrete containing fly ash, silica

Osama Ahmed MOHAMED, Omar Fawwaz NAJM

期刊论文

comparative study of the mechanical properties, fracture behavior, creep, and shrinkage of chemically based self-consolidatingconcrete

Mahdi AREZOUMANDI, Mark EZZELL, Jeffery S VOLZ

期刊论文

Effect of microlimestone on properties of self-consolidating concrete with manufactured sand and mineral

Fulin Qu, Wengui Li, Xiaohui Zeng, Zhiyu Luo, Kejin Wang, Daichao Sheng

期刊论文

Computational modeling of fracture in capsule-based self-healing concrete: A 3D study

期刊论文

Parametric study on seismic performance of self-centering reinforced concrete column with bottom-placed

期刊论文

The effects of mismatch fracture properties in encapsulation-based self-healing concrete using cohesive-zone

Luthfi Muhammad MAULUDIN, Chahmi OUCIF, Timon RABCZUK

期刊论文

Stress-strain relationship of recycled self-compacting concrete filled steel tubular column subjected

Feng YU, Cheng QIN, Shilong WANG, Junjie JIANG, Yuan FANG

期刊论文

Enhancing compressive strength and durability of self-compacting concrete modified with controlled-burnt

期刊论文

Optimization of machine learning models for predicting the compressive strength of fiber-reinforced self-compactingconcrete

期刊论文

Experimental research on self-stressing and self-compacting concrete filled steel tube columns subjected

Chengkui HUANG, Zuoqing SHANG, Peng ZHANG,

期刊论文

A hybrid machine learning model to estimate self-compacting concrete compressive strength

Hai-Bang LY; Thuy-Anh NGUYEN; Binh Thai PHAM; May Huu NGUYEN

期刊论文

Recycled glass replacement as fine aggregate in self-compacting concrete

Yasser SHARIFI, Mahmoud HOUSHIAR, Behnam AGHEBATI

期刊论文

Computational model generation and RVE design of self-healing concrete

Md. Shahriar QUAYUM,Xiaoying ZHUANG,Timon RABCZUK

期刊论文

An experimental study for optimization of high range water reducing superplasticizer in self compactingconcrete

Rahul DUBEY, Pardeep KUMAR

期刊论文

三峡升船机液压自升式模板施工技术

戴志清

期刊论文